Move existing boards into subdits split per arch

1 files changed, 0 insertions, 346 deletions

diff --git a/os/pc/devlm78.c b/os/pc/devlm78.c
deleted file mode 100644
index 617d5cb9..00000000
--- a/os/pc/devlm78.c
+++ /dev/null
@@ -1,346 +0,0 @@
-#include "u.h"
-#include "../port/lib.h"
-#include "mem.h"
-#include "dat.h"
-#include "fns.h"
-#include "io.h"
-#include "ureg.h"
-#include "../port/error.h"
-
-/* this driver doesn't implement the management interrupts.  we
- * leave the LM78 interrupts set to whatever the BIOS did.  we do
- * allow reading and writing the the readouts and alarm values.
- * Read(2)ing or write(2)ing at offset 0x0-0x1f, is
- * equivalent to reading or writing lm78 registers 0x20-0x3f.
- */
-enum
-{
-	/*  address of chip on serial interface */
-	Serialaddr=	0x2d,
-
-	/*  parallel access registers */
-	Rpaddr=		0x5,
-	Bbusy=		 (1<<7),
-	Rpdata=		0x6,
-
-	/*  internal register addresses */
-	Rconfig=	0x40,
-	Bstart=		 (1<<0),
-	Bsmiena=	 (1<<1),
-	Birqena=	 (1<<2),
-	Bintclr=	 (1<<3),
-	Breset=		 (1<<4),
-	Bnmi=		 (1<<5),	/*  if set, use nmi, else irq */
-	Bpowbypass=	 (1<<6),
-	Binit=		 (1<<7),
-	Ristat1=	0x41,
-	Ristat2=	0x42,
-	Rsmimask1=	0x43,
-	Rsmimask2=	0x44,
-	Rnmimask1=	0x45,
-	Rnmimask2=	0x46,
-	Rvidfan=	0x47,		/*  set fan counter, and read voltage level */
-	Mvid=		 0x0f,
-	Mfan=		 0xf0,
-	Raddr=		0x48,		/*  address used on serial bus */
-	Rresetid=	0x49,		/*  chip reset and ID register */
-	Rpost=		0x00,		/*  start of post ram */
-	Rvalue=		0x20,		/*  start of value ram */
-
-	VRsize=		0x20,		/*  size of value ram */
-};
-
-enum
-{
-	Qdir,
-	Qlm78vram,
-};
-
-static Dirtab lm78dir[] = {
-	".",			{ Qdir, 0, QTDIR},	0,	0555,
-	"lm78vram",	{ Qlm78vram, 0 },	0,	0444,
-};
-
-/*  interface type */
-enum
-{
-	None=	0,
-	Smbus,
-	Parallel,
-};
-
-static struct {
-	QLock;
-	int	probed;
-	int 	ifc;	/*  which interface is connected */
-	SMBus	*smbus;	/*  serial interface */
-	int	port;	/*  parallel interface */
-} lm78;
-
-extern SMBus*	piix4smbus(void);
-
-/*  wait for device to become quiescent and then set the */
-/*  register address */
-static void
-setreg(int reg)
-{
-	int tries;
-
-	for(tries = 0; tries < 1000000; tries++)
-		if((inb(lm78.port+Rpaddr) & Bbusy) == 0){
-			outb(lm78.port+Rpaddr, reg);
-			return;
-		}
-	error("lm78 broken");
-}
-
-/*  routines that actually touch the device */
-static void
-lm78wrreg(int reg, uchar val)
-{
-	if(waserror()){
-		qunlock(&lm78);
-		nexterror();
-	}
-	qlock(&lm78);
-
-	switch(lm78.ifc){
-	case Smbus:
-		lm78.smbus->transact(lm78.smbus, SMBbytewrite, Serialaddr, reg, &val);
-		break;
-	case Parallel:
-		setreg(reg);
-		outb(lm78.port+Rpdata, val);
-		break;
-	default:
-		error(Enodev);
-		break;
-	}
-
-	qunlock(&lm78);
-	poperror();
-}
-
-static int
-lm78rdreg(int reg)
-{
-	uchar val;
-
-	if(waserror()){
-		qunlock(&lm78);
-		nexterror();
-	}
-	qlock(&lm78);
-
-	switch(lm78.ifc){
-	case Smbus:
-		lm78.smbus->transact(lm78.smbus, SMBsend, Serialaddr, reg, nil);
-		lm78.smbus->transact(lm78.smbus, SMBrecv, Serialaddr, 0, &val);
-		break;
-	case Parallel:
-		setreg(reg);
-		val = inb(lm78.port+Rpdata);
-		break;
-	default:
-		error(Enodev);
-		break;
-	}
-
-	qunlock(&lm78);
-	poperror();
-	return val;
-}
-
-/*  start the chip monitoring but don't change any smi 
- *  interrupts and/or alarms that the BIOS may have set up. 
- *  this isn't locked because it's thought to be idempotent 
- */
-static void
-lm78enable(void)
-{
-	uchar config;
-
-	if(lm78.ifc == None)
-		error(Enodev);
-
-	if(lm78.probed == 0){
-		/*  make sure its really there */
-		if(lm78rdreg(Raddr) != Serialaddr){
-			lm78.ifc = None;
-			error(Enodev);
-		} else {
-			/*  start the sampling */
-			config = lm78rdreg(Rconfig);
-			config = (config | Bstart) & ~(Bintclr|Binit);
-			lm78wrreg(Rconfig, config);
-pprint("Rvidfan %2.2ux\n", lm78rdreg(Rconfig), lm78rdreg(Rvidfan));
-		}
-		lm78.probed = 1;
-	}
-}
-
-enum
-{
-	IntelVendID=	0x8086,
-	PiixID=		0x122E,
-	Piix3ID=	0x7000,
-
-	Piix4PMID=	0x7113,		/*  PIIX4 power management function */
-
-	PCSC=		0x78,		/*  programmable chip select control register */
-	PCSC8bytes=	0x01,
-};
-
-/*  figure out what kind of interface we could have */
-void
-lm78reset(void)
-{
-	int pcs;
-	Pcidev *p;
-
-	lm78.ifc = None;
-	p = nil;
-	while((p = pcimatch(p, IntelVendID, 0)) != nil){
-		switch(p->did){
-		/*  these bridges use the PCSC to map the lm78 into port space. */
-		/*  for this case the lm78's CS# select is connected to the PIIX's */
-		/*  PCS# output and the bottom 3 bits of address are passed to the */
-		/*  LM78's A0-A2 inputs. */
-		case PiixID:
-		case Piix3ID:
-			pcs = pcicfgr16(p, PCSC);
-			if(pcs & 3) {
-				/* already enabled */
-				lm78.port = pcs & ~3;
-				lm78.ifc = Parallel;
-				return;	
-			}
-
-			/*  enable the chip, use default address 0x50 */
-			pcicfgw16(p, PCSC, 0x50|PCSC8bytes);
-			pcs = pcicfgr16(p, PCSC);
-			lm78.port = pcs & ~3;
-			lm78.ifc = Parallel;
-			return;
-
-		/*  this bridge puts the lm78's serial interface on the smbus */
-		case Piix4PMID:
-			lm78.smbus = piix4smbus();
-			if(lm78.smbus == nil)
-				continue;
-			print("found piix4 smbus, base %lud\n", lm78.smbus->base);
-			lm78.ifc = Smbus;
-			return;
-		}
-	}
-}
-
-Walkqid *
-lm78walk(Chan* c, Chan *nc, char** name, int nname)
-{
-	return devwalk(c, nc, name, nname, lm78dir, nelem(lm78dir), devgen);
-}
-
-static int
-lm78stat(Chan* c, uchar* dp, int n)
-{
-	return devstat(c, dp, n, lm78dir, nelem(lm78dir), devgen);
-}
-
-static Chan*
-lm78open(Chan* c, int omode)
-{
-	return devopen(c, omode, lm78dir, nelem(lm78dir), devgen);
-}
-
-static void
-lm78close(Chan*)
-{
-}
-
-enum
-{
-	Linelen= 25,
-};
-
-static long
-lm78read(Chan *c, void *a, long n, vlong offset)
-{
-	uchar *va = a;
-	int off, e;
-
-	off = offset;
-
-	switch((ulong)c->qid.path){
-	case Qdir:
-		return devdirread(c, a, n, lm78dir, nelem(lm78dir), devgen);
-
-	case Qlm78vram:
-		if(off >=  VRsize)
-			return 0;
-		e = off + n;
-		if(e > VRsize)
-			e = VRsize;
-		for(; off < e; off++)
-			*va++ = lm78rdreg(Rvalue+off);
-		return (int)(va - (uchar*)a);
-	}
-	return 0;
-}
-
-static long
-lm78write(Chan *c, void *a, long n, vlong offset)
-{
-	uchar *va = a;
-	int off, e;
-
-	off = offset;
-
-	switch((ulong)c->qid.path){
-	default:
-		error(Eperm);
-
-	case Qlm78vram:
-		if(off >=  VRsize)
-			return 0;
-		e = off + n;
-		if(e > VRsize)
-			e = VRsize;
-		for(; off < e; off++)
-			lm78wrreg(Rvalue+off, *va++);
-		return va - (uchar*)a;
-	}
-	return 0;
-}
-
-extern Dev lm78devtab;
-
-static Chan*
-lm78attach(char* spec)
-{
-	lm78enable();
-
-	return devattach(lm78devtab.dc, spec);
-}
-
-Dev lm78devtab = {
-	'T',
-	"lm78",
-
-	lm78reset,
-	devinit,
-	devshutdown,
-	lm78attach,
-	lm78walk,
-	lm78stat,
-	lm78open,
-	devcreate,
-	lm78close,
-	lm78read,
-	devbread,
-	lm78write,
-	devbwrite,
-	devremove,
-	devwstat,
-};
-